setting bios boot partition arch virtualbox

Vgchange -ay Format the root partition mkfs.ext4 /dev/volgroup0/lv_root Mount the root partition mount /dev/volgroup0/lv_root /mnt Format the home partition mkfs.ext4 /dev/volgroup0/lv_home Create the home partition mount point mkdir /mnt/home Mount the home volume mount /dev/volgroup0/lv_home /mnt/home Create the /etc dirctory mkdir /mnt/etc Create the /etc/fstab file genfstab -U -p /mnt > /mnt/etc/fstab Check the /etc/fstab file cat /mnt/etc/fstab Preparing the hard disk (UEFI with encryption) See partitions/drives on the system (find the name of your hard drive) fdisk -l Start the partitioner (fdisk) fdisk /dev/ (substitute for your device name, example: /dev/sda or /dev/nvme0n1) Show current partitions p Create EFI partition g (to create an empty GPT partition table)ģ0 Show current partitions again p Finalize partition changes w Format the EFI partition mkfs.fat -F32 /dev/ (for example: /dev/sda1) Format the boot partition mkfs.ext4 /dev/ (for example: /dev/sda2) Set up encryption cryptsetup luksFormat /dev/Ĭryptsetup open -type luks /dev/ lvm Set up lvm pvcreate -dataalignment 1m /dev/mapper/lvm Vgcreate volgroup0 /dev/sda2 (or whatever the device name is of the second partition) Preparing the hard disk (UEFI) See partitions/drives on the system (find the name of your hard drive) fdisk -l = Start the partitioner (fdisk) fdisk /dev/ (substitute for your device name, example: /dev/sda or /dev/nvme0n1) Show current partitions p Create EFI partition g (to create an empty GPT partition table)ģ0 (for Linux LVM) Show current partitions again p Finalize partition changes w Format the EFI partition mkfs.fat -F32 /dev/sda1 (or whatever the device name of the first partition is) Set up lvm pvcreate -dataalignment 1m /dev/sda2 (or whatever the device name is of the second partition) Vgchange -ay Format the root partition mkfs.ext4 /dev/volgroup0/lv_root Mount the root partition mount /dev/volgroup0/lv_root /mnt Format the home partition mkfs.ext4 /dev/volgroup0/lv_home Create the home partition mount point mkdir /mnt/home Mount the home volume mount /dev/volgroup0/lv_home /mnt/home Create the /etc dirctory mkdir /mnt/etc Create the /etc/fstab file genfstab -U -p /mnt > /mnt/etc/fstab Check the /etc/fstab file cat /mnt/etc/fstab Lvcreate -l 100%FREE volgroup0 -n lv_home (or use something like '-L 250GB' if you want to make the volume size lower) Scan for wireless access points: station scan View a list of detected networks: station get-networks Connect to a wireless network: station connect Preparing the hard disk (standard, no-UEFI) See partitions/drives on the system (find the name of your hard drive) fdisk -l Start the partitioner (fdisk) fdisk /dev/ (substitute for your device name, example: /dev/sda or /dev/nvme0n1) Show current partitions p Create LVM partition o (to create an empty non-gpt partition table)Ĩe Show current partitions again p Finalize partition changes w Set up lvm pvcreate -dataalignment 1m /dev/

You’ll want to check hardware compatibility with your Wifi card and Linux, and then resume installation at a later date. Note: If you don’t see a Wifi device there, and you’re sure you do have WiFi capability, you shouldn’t proceed any further with installing Arch. Take note of the device name for your WiFi device, we’ll need it later. Check if there is an Internet connection (if on wired) ip addr show For WiFi, you can use iwctl Access the iwd prompt: iwctl Obtain a list of Wifi devices in your system: device list Note: The process will erase everything on the drive. Once that’s finished, boot your computer with that flash drive. If you plan to use UEFI, make sure that UEFI is enabled in the BIOS before you boot into the Arch installerĭownload usbimager: Use usbimager to turn your flash drive into Arch Linux installation media.

Setting bios boot partition arch virtualbox